If you’ve been ignoring water problems in your basement, there’s a high possibility you’re dropping up to half of your home’s living space, given the current cost of housing going in, that’s a significant loss. While water in a basement can come from various sources, almost all these issues can be resolved. For many, the most straightforward solution is a sump pump installation, and it does the task at a reasonable cost for the majority of us. However, without the appropriate equipment, the house will flood, causing significant damage.
When it comes to your home, you might want to think about buying and installing a sump pump. A sump pump is equipment that removes any water that has accumulated in a home’s basement. A sump pump installation in the basement is helpful in areas where flooding is common because it can be used to speedily remove the water, saving you thousands of dollars in potential home repairs.
What is a sump pump?
The sump pump is installed in the basement’s lowest level. The sump pump works with a waterproofing system to channel water to the sump basin and out of your house through a drainage system, which helps keep your basement dry.
HydroHelp911 Basement Sump Pump Installation Process
1. Choose a location and get the site ready.
First, determine the lowest point in your basement, which is usually where you first notice moisture accumulation. Next, dig a hole large enough and deep enough to cater the sump pump installation. The top edge of the sump pump must be able to sit flush with the floor level.
Digging a hole in a concrete basement floor is done more efficiently. First, the concrete is broken with a sledgehammer or a jackhammer. Then, the HydroHelp911 basement sump pump installation team will continue digging after penetrating the masonry until the cavity can accommodate the pump basin.
2. Prevent clogs by inserting the sump pump into the hole.
The most impactful sump pumps have two weep holes that allow water to enter from the sides and underneath. If your sump pump lacks these critical incisions, you will need to drill them yourself. Finally, enclose a layer of filter fabric around the basin’s exterior to keep silt and sludge from clogging.
3. Next, the HydroHelp911 sump pump installation experts
Will add 2 or 3 inches of gravel to the desired depth, then position a paver or fieldstone on top of the gravel to form a sustainable platform. Finally, the team will backfill the hole with excavated dirt around the perimeter of the sump pump. The unit should not flutter at this point.
4. Check the float valve on the sump pump.
The sump pump’s float valve must be free to move up and down to function correctly. If the level of water increases, the float rises with it, and the pump activates. Before proceeding, it is critical to test the float valve.
5. Connect a hose or pipe from the exterior of the house to the valve.
The check valve, which directs water away from the sump, is vitally valuable. Therefore, the sump pump installation team of HydroHelp911 will now run a flexible discharge hose or a length of PVC pipe between the valve and the home’s exterior.
A large hole is made for the hose or pipe to fit through where the output meets the basement wall. A drill/driver done with a hole-saw bit is used to accomplish this. After the team has inserted the pipe, sealant will be used to fill any gaps.
6. Check for leaks and test the sump pump.
Finally, the pipes are connected now and run through their paces. Next, the basement sump pump installation team will fill the basin almost to the brim with water. Then, the float should rise, the pump should activate, and the water should drain. Lastly, the team inspects the connections for leaks, and then they place the lid over the basin if everything is in working order.
7. Cover the pump’s hole with concrete.
The final step of the HydroHelp911 basement sump pump installation is to cover the pump’s hole. This is usually done with concrete – Mix a small mixture of cement mortar and spread it around to cover everything except the sump pump lid.
Professionals must do the basement sump pump installation as the installation process involves digging the ground. These underneath ground have gas and sewer lines that need to be taken care of and not disturbed.
If your basement in Gastonia, NC, is not waterproofed and you have water accumulation issues, then you must contact a sump pump installation expert HydroHelp911. With sump pump installation and waterproofing services by HydroHelp911, owners can prevent their basement from flooding in the future.
Frequently Asked Questions:
How is an exterior sump pump installed?
Sump pumps can even be used to solve exterior drainage problems. They drain standing water from outdoor areas and gardens in the same way they do inside your home. They can also help to protect your foundation by diverting water away from it. Because the external pump will need to deliver a larger surface area than most basements, a professional basement sump pump installation contractor like HydroHelp911 may choose to dig inlet lines and catch basins that will push water into the sump pit from various locations throughout the landscape.
Most sump pits have pipelines that drain into the gutters, but it is essential to check with your local municipality to confirm legality. Because gas and sewer lines must be taken care of in the surrounding area, installing an exterior sump pump should always be done by a professional. Exterior sump pumps are best suited for mild winter climates. Freezing and expanding of water in the system can cause the pump to fail unexpectedly. Without this type of intervention, most sump pumps have a lifespan of about ten years.
Is it necessary to maintain the sump pump?
The sump pump needs to be serviced regularly. You can’t just fit it and neglect it. It is strongly advised that you have it checked at least once a year. If the pump is used more regularly, it is recommended to check several times a year, as dirt, gravel, sand, and other forms of debris can clog it and prevent it from functioning optimally. Before performing any general maintenance, it is always necessary to disconnect it from the electrical current to avoid the risk of electrocution.
How does a sump pump check valve function?
The check valve only allows water to flow in one direction. When the pump generates pressure, it will enable water to be discharged through the discharge pipe. When the water level falls, and the pump shuts down, the check valve prevents the water in the outflow pipe from flowing back into the pump and causing it to run. It is vital to install the check valve in the right direction to ensure the water is discharged and not drained back. Install the check valve in the correct order, so it allows discharge and not drain-back.
What are the various types of sump pumps?
There are different types of pumps for separate installations, so not all sump pumps are created equal. To begin, there are two basic types of sump pumps. One is referred to as a pedestal, while the other is referred to as a submersible. The pedestal pump is mounted on a pedestal above the pit. It is simple to service and repair problems, but it is out in the open. The submersible pump is installed inside the hole and is sealed to prevent an electrical short circuit as it comes into more significant contact with the water. However, because of its proximity within the pit, it is more difficult to service.
What are the advantages of installing a sump pump?
- Prevent flood damage- Water can enter a basement and cause extensive damage during heavy storms. A good sump pump can efficiently remove before it gets sufficiently severe damage.
- Protect your home from mold and mildew-Whatever volume of water that enters your basement or crawlspace raises humidity, forming a breeding ground for mold and mildew, these growths are both unaesthetic and undesirable to smell, and they can cause or contribute to health problems such as skin irritation and itchy eyes. A sump pump will aid you in maintaining your humidity levels under control.
Why should you have a battery backup?
The sump pump is connected to the home’s electrical system. Therefore, your sump pump will not function unless linked to a battery backup in a power outage. Because heavy rains frequently accompany power outages, it is critical to ensure that your sump pump can operate during power outages.