Search
Close this search box.

Sump Pump Installation in Crawl Spaces for Residents of Charlotte, NC By HydroHelp911

Table of Contents

Prevent crawl space flooding by introducing and maintaining a sump pump

There’s no more reliable way to prevent a crawl space flood than with a sump pump. Although it isn’t the greatest DIY-friendly of projects, installing a sump pump in your basement, crawl space, or backyard will prevent your house from warping, rot, mildew, and rust caused by water erosion.

A sump pump uses a submersible platform that rises and falls with the water board. When flooding causes the float to grow, a switch automatically turns on, and the pump begins to remove water, draining it through a pipe to the outdoors.

Sump pump fitting generally needs a professional. These are the measures involved:

Sump Pump Installation Method in 8 Steps by HydroHelp911:

  1. The process starts with placing the sump basin upside down on the foundation floor and identifying its outline. (When determining a place to install the pump, factor in a proper sewerage plan and vicinity to a ready power source.)
  2. Next, use a destruction hammer to chop into the concrete floor and dig a hole deep to set the sump basin inside it, wash with the floor.
  3. Before installing the bay in the spot, cover its exterior base with filter fabric. It will prevent residue from clogging the pump device.
  4. Then, after the basin is set inside the hole, put various bands of gravel inside it. Next, lay a stone paver on top of that rock. It will retain gravel out of the pump and give a firm platform for it.
  5. A one-way inspection valve will need to be attached to a PVC pipe to run up the wall and out of the foundation. While the design of this pipe will vary from house to house, its usual purpose is to take water up and out of the house. When digging a hole for the line in the house wall, use a hole saw and seal the area thoroughly with a paintable caulk. It will give a watertight seal. The PVC pipe should reach outdoors and empty through a downspout. If the grading of the land is inadequate for proper drainage, either invest in regrading the yard or in an even more extended downspout to ensure water is carried away. Some homeowners may be motivated to run a drain line from their sump pump into a local storm drain. However, most locales won’t allow this. Before connecting a sump pump, check with your town to see which waste options are allowable.
  6. Fill the aperture around the sump basin with new concrete to finish the fitting, mixed in a trough with a hoe.
  7. Fill in throughout the bay to the top with cement and smooth it off with a sharp trowel.
  8. After powering up your pump, examine it by filling the basin with water. Assume you ever need to renew the pump. In that matter, you can do this by quickly switching off the power to the assembly, disconnecting the old pattern from the discharge device, reconnecting and leveling a new pump, and examining it the same as you did against the initial connection.

Fixing Crawl Space Sump Pumps and Exterior Sump Pits

Not every sump pump is built the same. The most straightforward sump pumps are rammed into an outlet, but other designs have backup batteries that run the pump even when there is a power outage. This subsequent power system can come in handy when inclement weather and replace the battery every couple of years.

How do you fit a crawl space sump pump?

Installing a sump pump in the crawl space needs slightly various preparations and supplies. The surface inside your crawl space may not be even, and below-grade water may form pools of holding water in low spots. Consider accessible entrances, like the basement install, a proper drainage plan, and an active power source when installing the basin. The method for installing these basins and discharge systems is the same until it finishes the hole for the basin. Rather than splashing concrete, it’s suggested that pea gravel be united up to the basin’s lip for peculiar drainage.

How do you connect an exterior sump pump?

Sump pumps can be installed to fix exterior drainage problems. They work the same as inside your house to drain standing water from outside entertaining spaces and yards. They can also preserve your foundation by redirecting water away from home because the external pump will require a larger coverage area than most foundations. A professional constructor may opt to dig inlet lines and grab basins to fill the sump pit from separate points around the landscape.

From there, most sump pits have lines that drain into the road gutters, but check your regional municipality to verify permissibility. Installing an exterior sump pump should be performed by a trained professional, as there are obstacles like gas and sewer lines nearby. Exterior sump pumps are best suited for moods with mild winters. Water freezing and increasing in the system can ruin the pump. Without this kind of intervention, most sump pumps last for almost ten years.

What can you do to keep your crawl space dry?

Sump pumps remove water that’s previously collected, but they don’t help. While they act as crucial emergency aids and damage reducers, they’re just one critical part of a complete crawl space moisture-reducing system.

Along with introducing a crawl space sump pump, you should consider other measures.

  • Crawl Space Ventilation
  • Mold embellishments in darkness and dampness. Automatic air pumps expel moisture and potentially hazardous gases like radon from your crawl spaces and into the encompassing environment.

    Watch our video – 

  • Crawl Space Encapsulation
  • Most moisture enters your crawl space from the neighboring dirt and foundation. Encapsulation retains that moisture from getting inside the crawl space in the first place.

    Watch our video – 

  • Crawl Space Moisture Barriers
  • Like cement encapsulation, moisture barriers inhibit mold, water, and insects from getting inside of your crawl areas.

    When you mix wet crawl space solutions like those above with crisis measures like crawl space sump pumps, you can stop moisture from growing in and relocate excess water out if a flood or foundation rift lets water flow into the crawl space.

    Watch our video – 

    Find Peace of Mind and Reduce Damage

    Installing a crawl space sump pump can prevent you from worrying that pests, mold, and asset destruction are developing beneath your floors. Operate with a basement waterproofing professional to locate and install the right crawl space sump pump for your home.

    You’ll enjoy not just a disinfectant, dryer crawl space area but also the more comprehensive peace of mind that originates with knowing every aspect of your home is safe and sound.

    HydroHelp911 deals with a lot of rain attacking houses. Unfortunately, sometimes this rain finds its way into your crawl space, and you are left with dangerous standing water. Several times, in these circumstances, our team will recommend a sump pump installation. Below are some common questions that clients ask us before moving forward with a sump pump installation.

    Why do I want a sump pump?

    Sump pumps are required when standing water collects in your crawlspace, and there is no way for it to drain typically. Many houses have a low-point drain that will provide water to go out of the crawlspace, but some houses either don’t have one or have it fixed in an area not the most profound point of the crawlspace. By placing a sump pump at the lowest point of the crawlspace (trenching), water will secure its way to the pump and be released from the space.

    What does a sump pump installation involve?

    A standard sump pump installation begins with digging a deep hole at the deepest point of the crawlspace, generally between 2 to 3 feet deep. Next, fill the aperture with a couple of inches of waste rock, and a sump basin will be introduced that is approximately 18 X 22 inches. Enclosing the bay will be a layer of the drain. Next, a pump will be plumbed in (by a backflow design) to the release point to take the water outside of the crawlspace.

    How stable are sump pumps?

    A sump pump is similar to any appliance that you have in your house. Eventually, it will crash and need to be replaced. There are many reasons why sump pumps fail, but all of our pumps come with a 5-year warranty. The most apparent reason for pump malfunction is when the release point (typically your storm flows) is obstructed, causing the pump to overwork itself. Nevertheless, we suggest installing a sump pump notification so that if the pump breaks, it will warn you of possible flooding before damages occur.

    Are you looking for wet crawl space or basement solutions in Charlotte, North Carolina? HydroHelp911 Basement and Crawl Space Waterproofing have the tools and experience to help. Schedule your crawl space sump pump installation today by calling us at 704-396-5008.

    Contact HydroHelp911 Today!

    HydroHelp911 will do everything we can to ensure your experience with us is excellent.

    "*" indicates required fields

    I need help with :

    By providing your mobile number on the submitted form, you grant HydroHelp911 permission to send you SMS messages for communication and updates regarding our products and services. SMS messages may include but are not limited to: Important service notifications | Scheduling reminders and changes. Standard messaging and data rates may apply. You can opt out of receiving SMS messages at any time by replying with “STOP” to any message. We respect your privacy and will not share your information with any third parties.

    CHECK OUT RECENT POST

    Do You Have Basement or Crawl Space Questions?

    If you reside in North Carolina and need a highly skilled foundation repair, basement waterproofing or crawl space repair company, look no further! HydroHelp911 is ready to restore the life of your basement or crawl space!